1.規格型號和安規認證
MODEL NU*ER AND SAFETY CERTIFICATION 1-1 品名規格：系列號+額定電流+額定電壓+認證*號Model Number: Part Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
5GFU 5A 250V 1)系列號 Part Number
2)額定電流 Rated Current
1） 2） 3） 3)額定電壓 Rated Voltage1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流： 63mA~15A
Rated Current: 63mA~15A
額定電壓;125V/250V AC
Rated Voltage:125V/250V AC
1-3標示Marking
保險絲上需有下列標示
The fuse shall have the following marking:
規格：特性*號+額定電流+額定電壓
Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA250V 1A~15A:_A250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
|
|
63mA~15A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍
SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構
OUTLINE DRAWING AND STRU*URE
3-1 工程圖（單位：mm）
Outline Drawing and Dimensions(Unit:mm)
3-2結構
Structure
| 編號 No. | 元件 Component | 材質 Material | 數量 Quantity |
| (1) | 熔絲 Wire | 合金 Alloy | 1 |
| (2) | 銅帽 Cap | 黃銅鍍鎳 Br* with mickel plated | 2 |
| (3) | 本體 Body | 玻璃管 Gl* Tube | 1 |
| (4) | 引線 Lead | 鍍錫銅線 Tinned Copper wire | 2 |
4.外觀及形狀
APPEARANC* AND CONFIGURATION
4-1外觀：不應有破碎、明顯的汙斑
Appearances:There shall no fragmentation and of remarkable blotch.
4-2形狀：帶腳的保險絲
Configuration:Axial Leaded Fuse.
5.物理特性
PHYSICAL CHARA*ERISTIC
5-1 拉力測試
Tensile test
沿端子的軸向施加10N的拉力，持續1分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELE*RICAL CHARA*ERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
| 35A | 250V | AC |
b、Electrical characteristics
Time Lag(国标、欧标 CCC/VDE)
RATED CURRENT | 2.1IN | 2.75IN | 4IN | 10IN | |||
63mA to 100mA | Max. | Min. | Max | Min. | Max. | Min. | Max. |
2 min. | 200mS | 10S | 40mS | 3S | 10mS | 300mS | |
Above 100mA to15A | 22min | 600mS | 10S | 150mS | 3S | 20mS | 300mS |
| RATED CURRET | 2.1IN | 2.75IN | 4IN | 10IN | ||
| 63mA to 100mA | Max. | Min. | Max. | Min. | Max. | Max. |
| 30 min | 10ms | 500ms | 3ms | 100ms | 20ms | |
| Above 100mA to6.3A | 30min | 50ms | 2s | 10ms | 300ms | 20ms |
| Above 6..3A to15A | 30min | 50ms | 2s | 10ms | 400ms | 40ms |
美标（UL）
c、Temperature character
When 100% of rating the temperature rise doesn’t exceed75℃.
d、Approvals
| Catalogue number | Rated current | Voltage | 参照美标、欧标 |
| 5GFUP/5GTUP | 63mA~15A | 125V/250V |
7.環境特性
ENVIRonMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
Operating Temperature:-5℃~60℃
7-2 保存條件
Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放3年
On average, It can be stored below the relative humidity or 75% for 3 years.
在非露*，相對濕度為95%下*多可存放30天。
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
SOLDERING PAAMETERS
8-1波峰焊
Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2手工焊錫
Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
OTHER *TICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於150℃ 烘烤時間：50s Max. The temperature should be sel under150℃,roast time:50s Max.
19228131880微信