|
技术参数 Technical specifications |
||
|
·低价格、高可靠Low price、reliable quality |
外形图片
PICTURE ATTACHED ON THE END OF PAGE |
|
|
·效率高,工作温度低High efficience, low working temperature |
||
|
·软启动电流,有效降低AC输入冲击soft start electric current |
||
|
·有短路保护,过载保short circuit and overload protection |
||
|
·100%满负荷烧机测试100% enough ageing test |
||
|
·内装EMI滤波器、纹波极小inner EMI lead to the smallest wave |
||
|
型号Model |
CHISONY-1202000 |
|
|
INPUT DATA |
||
|
最大输入电压范围Input Voltage Rage |
96～264VAC |
|
|
额定输入电压 Rated Voltage |
100-240VAC |
|
|
频率范围Variation Frequency Rage |
47-63HZ |
|
|
额定频率Rated Frequency |
50/60HZ |
|
|
冷启动电流cool start current |
< 30A/240Vac |
|
|
OUTPUT DATA |
||
|
性能Performance |
直流输出电压DC OUTPUT |
|
|
额定输出电压Rated output voltage |
12V,24V,36V,48V,60V,72V,84V,120VDC |
|
|
输出额定电流及功率Rated current and Watts |
2-60A 24W- 2000W |
|
|
过流点Peak current Point |
105-150% |
|
|
纹波及噪音(注3)Ripple and noise |
<300mVp-p240Vac |
|
|
启动、上升、保持时间start、up、maintain |
200ms,50ms,30ms |
|
|
负载调整率(注5)Bear adjusted frequency |
±10% |
|
|
直流输出功率DC output power |
240W |
|
|
详细要素DETAILS DATA |
||
|
效率efficiency |
Max 81% at 240Vac |
|
|
功率因素 PFC |
0.65 |
|
|
过载保护overload protection |
105--150% MAX |
|
|
操作温度Working Temperature |
-10℃～40℃ |
|
|
储存温度Storage Temperature |
-40℃---80℃ |
|
|
工作湿度relative humidity |
-0℃～+40℃: 5%～90%RH AT 72Hrs Load |
|
|
平均故障隔离时间 MTBF |
100k hours at max. at 25°C |
|
|
耐压性Withstand Voltage |
IP/OP 2KVAC; IP/FG 1.5KAVC; OP/FG 0.5KVAC |
|
|
隔离电阻Isolation Resistance |
输入输出时间IP/OP：100M Ohms |
|
|
抗震性against shock character |
周期是10分钟; 10～500Hz,2G，10min./1period, |
|
|
海拔Altitude |
低于10000英尺Less Than 10,000 foot--- |
|
|
接口类型interface type |
DC头 航空头 |
|
|
外形尺寸outside size |
|
|
|
安全标准safe standard |
IEC60950-1,CE |
|
|
注意事项REMARKS |
||
|
1、以上参数测试条件为：220VAC输入，额定负载，25℃70% RH.湿度。 The above specification test condition:220VAC input, Rated bear ,25℃70% RH moisture degree |
||
|
2、纹波测试：20MHz用双绞线，终端用0.1uF&47uF电容器短路 wave test:20MHz used A12"double axes. Terminal use 0.1uF&47uF capacitance short circuit |
||
|
3、线路调整率度测试：满负载时进线最低电压到最高电压 circuit adjust rate test: enough overload inline from the lowest voltage to the highest voltage |
||
|
4、负载调整率测试：负载从0%到100%，其他输出为60%或80％额定负载。 Bear adjust rate test: bear is from 0% to 100%，other output is 60% or80% rated bear |
||
|
5、各输出可达最大电流，但总负载不可超过最大输出功率。 All output can reach the biggest electric current, but total bear can not be over the biggest output power |
||