品牌
型号
种类
额定电压
额定电流
接触电阻
绝缘电阻
产品性质
营销方式
营销价格
加工定制
货号
3C额定电压范围
是否跨境出口专供货源
1 产品用途Application
HKW9700-B-C型热保护器具有体积小、外壳绝缘、动作灵敏、寿命长等特点，
适用于新能源电池，电机、电源，光灯镇流器、变压器、汽车马达、集成电路及
一般电气设备的过热过流双重保护作用。
HKW9700-A-B-C thermal protector has small dimension; insulation shell;
sensitive and long life time. Its widely use in new energy battery;
motor; power; ballast; transformer;integrated circuit and
electrical equipment’s overheat and overload double protection.
2 结构特点Structural features
HKW9700-B-C系列热保护器是采用一定几何形状的双金属片，无需辅助机构，仅靠双金属片的自身感温和电流热效应，使双金属元件的状态发生快速变化，直接带动触点实现自动切断和接通电路，起到过热、过载保护作用。
HKW9700-A-B-C thermal protector use unique bimetal and don’t need more auxiliary parts. Using bimetal Self-sensing temperature and Current thermal effect to change the bimetal’s shape to control the electric circuit cut off or contact on. Overheat and overload double protection.
3 安规认证 (certification)：CQC18002202372 CQC180022022369
UL E502318
KC ZU02105-19001
TUV B1039300001
ROHS AGC01409190101101-001 REACH
4 产品外形dimension
Plastic shell塑壳： 15*5.4*2.4MM; 12*5.4*2.4MM; 10*5*2MM
Contact type动作分为：常开/常闭 Normal closed or normal opened
热保护器的外壳 可以配安装支架。Optional mounting bracket
5 产品性能performance
5.1额定电流rated power(COS∮=0.7)DC 12V-8A 24V-4A、AC 250V 2A
5.2断开温度action temp：30℃～150℃; 复位温度reset temp 20℃～110℃
5.3抗拉力试验:产品的引线端应能承受大于或等于20N拉力,导线无断裂、滑出。
Tensile test:≥20N，No breaks or slips out of the wire
5.4绝缘电压:Insulation voltage
a.产品在断开时的引线之间应能承受AC660V,历时1min而无击穿闪络现象;
In the power off state the insulation voltage between two wires should accept AC660V one minute withoutbreakdown and flashover.
b.产品引线与绝缘外壳之间能承受AC1800V,历时1S而无击穿闪络现象;
The insulation voltage between the wires and shell should accept AC1800V 1 second withoutbreakdown and flashover.
5.5绝缘电阻:在正常条件下,引线与绝缘外壳之间的绝缘电阻在100MΩ以上。
Insulation resistance:≥100MΩ
5.6接触电阻:产品的接触电阻应不大于50mΩ。
Contact resistance：≤50mΩ
5.7耐高温试验:产品置于额定动作温度50℃的空气环境中保持96h。
High temperature test：The product is kept in an air environment over 50 °C for 96 h
5.8耐低温试验:产品置于-40℃空气环境中保持96h。
Low temperature test：The product is kept in an air environment of -40 °C for 96 h
5.9抗振试验: 热保护器应能承受振幅1.5mm,频率变化10～55Hz，扫描变化周期3～5次/min，
振动方向X、Y、Z，每个方向各连续振动2h。
Anti-vibration test：The thermal protector should be able to withstand an amplitude of 1.5mm, a frequency change of 10 to 55Hz, and a scan change period of 3 to 5 times/min.
The vibration directions X, Y, and Z are continuously vibrated for 2 h in each direction.
5.10跌落试验:产品自0.7m高度自由落下1次。
Drop test：The product is free to fall from a height of 0.7m one time.
5.11抗压试验:产品应能承受100N静压力1min。
Compression test:The product should be able to withstand 100N static pressure for 1min
5.7,5.8,5.9,5.10,5.11项试验后应满足下列条件:
The additional condition after the 5.7---5.11 test.
a. 断开温度变化应在初期值的+7℃以内;
The tolerance of off temp within±7℃
b.接触电阻应在100mΩ以下;
Contact resistance≤100mΩ
c.外形应无明显变形;
he shape should be free of obvious deformation
d.导线无开裂损伤。
No cracking damage to the wire
6 寿命 life time
产品在额定电压、电流、功率因数为0.7的条件下,外加热源使其动作4000次,应满足下面条件:
The product is rated at voltage, current and power factor of 0.7.after 4000 cycles action
a断开温度变化应在初始值的+5℃以内; The tolerance of off temp within ±5℃.
b接触电阻应在50mΩ以下; contact resistance≤50mΩ.
c继续试验至6000次后能动作;cycle life time over 6000 times.
7 其它事项:matters need attention
7.1断开温度检测的升温速率应控制为1℃/1min;
7.2The product cannot withstand strong impact and pressure during
8 热保护器动作复位温度参考表action /reset temperature reference table
序号 item | 断开温度 off temp | 闭合温度 Reset temp | 序号 item | 断开温度 off temp | 闭合温度 Reset temp |
30 | 30 | ≥20℃ | 95 | 95 | 70 |
35 | 35 | ≥25℃ | 100 | 100 | 70 |
40 | 40 | ≥30℃ | 105 | 105 | 75 |
45 | 45 | ≥33℃ | 110 | 110 | 75 |
50 | 50 | ≥35℃ | 115 | 115 | 80 |
55 | 55 | 42 | 120 | 120 | 85 |
60 | 60 | 45 | 125 | 125 | 85 |
65 | 65 | 48 | 130 | 130 | 90 |
70 | 70 | 50 | 135 | 135 | 95 |
75 | 75 | 53 | 140 | 140 | 100 |
80 | 80 | 55 | 145 | 145 | 100 |
85 | 85 | 60 | 150 | 150 | 105 |
90 | 90 | 65 | 155 | 155 | 110 |
